田林县飞剪 Flying scissors
精诚合作，互利共赢，共谋辉煌！亲爱的【飞剪 Flying scissors】客户您好，感谢您浏览五冶机械官方企业网站！多年来，河南五冶机械制造有限公司坚持以研发为生存之本，不断地提升新技术在【飞剪 Flying scissors】产品中的应用！ 不负韶华砥砺行，如果您想了解更多的【飞剪 Flying scissors】产品新技术在实际中的应用情况，请致电五冶机械【飞剪 Flying scissors】技术工程师
，了解更多资料！
启停式飞剪：
| 型号： | 3#-CA |
| 剪切方式： | 回转式 |
| 倍尺长度： | ≥15m |
| 箱体： | 焊接箱体 |
| 工作制度： | 启-停工作制 |
| 剪切速度： | 2~8m/s |
| 剪切精度： | ±20mm |
| 轧件材质： | 普碳钢、低合金钢 |
| 剪切温度： | ≥850℃ |
| 碎断长度： | ≤1000mm |
| 切头、切尾长度： | 50~300mm |
| *剪切力： | 120KN |
| *剪切面积： | 1000mm2 |
| 最短剪切周期： | 2s |
| 剪刃宽度： | 200mm |
| 电机型号： | ZFQZ-315/21 |
| 电机功率： | 150KW |
| 功能： | 切头、切尾、事故碎断、倍尺分断 |
| 控制设备： | 控制柜800×1000×2200 2面 |
| 检测设备： | 热金属检器：HMD8-4CD1 1台 |
| 码盘：EL1024 1台 | |
| 码盘：EL0360 1台 | |
| 接近开关：Ni15-S30 1只 |
圆盘飞剪是由成对的圆盘刀片组成，这种飞剪一般用在小型车间，将它安装在冷床前对长轧件进行粗剪，使进入冷床的轧件不致太长。或者将它安装在精轧机组前对轧件进行切头，以保证精轧机组的轧制过程顺利进行。
圆盘式飞剪所以能横向剪切运动着的轧件，主要是由于刀盘轴线与轧件运动方向倾斜一定角度，并且使圆盘刀片圆周速度在轧件运动方向上的分速度与轧件运动速度相等。轧件进入和离开圆盘刀片是通过诱导板实现的。圆盘式飞剪的缺点是剪切断面是倾斜的，但对于切头或在冷床前粗剪轧件影响不大。由于这种飞剪工作可靠，结构简单，并可应于轧制速度达10米/秒以上的场合，因而在小型车间得到了较广泛的应用。这种飞剪除了采用连续工作制外，也可采用启动工作制。
Start-stop flying scissors:
| Model number: | 3#-CA |
| Shear mode: | Rotary type |
| Double ruler length: | 15 m or more |
| Box: | Welded casing |
| Working system: | Start-stop system |
| Shear rate: | 2~8m/s |
| Shear accuracy: | Plus or minus 20 mm |
| Rolling material: | Common carbon steel, low alloy steel |
| Shear temperature: | 850 ℃ or higher |
| Breaking length: | 1000 mm or less |
| Length of cutting head and tail: | 50~300mm |
| Maximum shear force: | 120KN |
| Maximum shear area: | 1000mm2 |
| Minimum shear period: | 2s |
| Cutting edge width: | 200mm |
| Motor model: | ZFQZ-315/21 |
| Motor power: | 150KW |
| Function: | Head cutting, tail cutting, accident breaking, double scale breaking |
| Control equipment: | Control cabinet 800 x 1000 x 2200 2 sides |
| Testing equipment: | Hot metal detector: HMD8-4CD1 1 PCS |
| Code disk: EL1024 1 PCS | |
| Code disk: EL0360 1 PC | |
| Proximity switch: Ni15-S30 1 piece |
Disc flying shears can transverse shear moving rolling parts, mainly because the axis of the cutter head and rolling parts of the direction of the tilt Angle, and make the circular speed of the disc blade in the direction of rolling parts of the motion of the partial speed and rolling parts of the speed. Rolling into and out of the disc blade is achieved by the induction plate. The disadvantage of disc shear is that the shear section is inclined, but it has little effect on the cutting head or rough cutting in front of the cold bed. Because this kind of flying shear is reliable, simple in structure, and can be used in the rolling speed of more than 10 m/s, so it has been widely used in small workshops. This kind of flying cut off the use of continuous working system, but also can be used to start working system.Disc flying shears:
Disc flying shear is composed of a pair of disc blades. This kind of flying shear is generally used in small workshops. It is installed in front of the cold bed for rough cutting of long rolled pieces, so that the rolled pieces entering the cold bed are not too long. Or it can be installed in front of the finishing mill group to cut the rolled parts to ensure the smooth rolling process of the finishing mill group.
学党史知党情，企业发展跟党走！！如何让五冶【飞剪 Flying scissors】质量稳定可靠，创造客户价值，为社会提供匠造臻品的产品，才是五冶人努力的方向！精工筑基，创新领航赢未来！
五冶人愿与您携手共筑中国梦，恭祝各位朋友生意兴隆，财源广进！！
地址：河南省焦作市温县谷黄路
服务热线：13938265594
手机：13938265594
邮箱：137545002@qq.com